ADVICE & GUIDES

Looking after
your shepherd hut

A little regular care goes a long way. Keep the finish protected, the air moving and the water system ready for winter.

A quiet country lane and fields in the evening light

01 / TIMBER CLADDING

External maintenance
Wooden shepherd hut

A timber-clad shepherd hut needs very little looking after, but a small amount of regular attention will keep it in good condition for decades.

Protect the finish

The featheredge cladding should be repainted as and when it needs it. In our experience, that is typically every two to three years, though it depends a great deal on how exposed your hut is to sun, wind and rain.

Give the joinery extra care

The windows and doors are the most maintenance-heavy part of the hut and deserve the closest attention. Keep them well stained and re-treat them regularly, before the finish starts to wear thin rather than after. Use a product compatible with the existing finish.

Keep the underside clear

Keep the ground beneath the hut clear so that air can flow freely under the floor. This allows anything that does get damp to dry out naturally.

02 / METAL CLADDING

External maintenance
Metal-clad shepherd hut

A metal-clad shepherd hut is very low-maintenance. The factory-finished corrugated cladding does not need regular repainting or treatment, so most of your attention can go on the joinery.

Check the metal finish

Give the cladding an occasional gentle clean and check for scratches, damaged coatings or signs of corrosion. Follow the cladding manufacturer’s cleaning and repair advice, particularly if your hut is in an exposed or coastal location.

Look after windows and doors

Keep the timber windows and doors well stained and re-treat them regularly, before the finish starts to wear thin rather than after. Use a product compatible with the existing finish.

Let air flow underneath

Keep the ground beneath the hut clear so that air can circulate under the floor, allowing anything that does get damp to dry out naturally.

03 / BEFORE FREEZING WEATHER

Winterisation

If your hut will be unused over winter, the water system must be fully drained to help prevent frost damage. Water trapped in pipes, taps or fittings can freeze and cause damage.

01

Switch off and let the heater cool

Turn off the incoming water supply and switch off the water heater. Allow the water to cool before draining.

02

Drain the heater and pipework

Drain the heater in accordance with its manufacturer’s instructions and use the drain points provided for your hut’s plumbing system. Opening the taps alone may not empty the whole system.

03

Open every tap

Fully open all hot and cold taps, including the shower controls, to allow water to drain. Leave them open while the hut is out of use.

04

Check the places water can collect

Do not overlook the shower hose and head, toilet cistern, outside supply hose, filters or other water-fed fittings. Follow the instructions for the equipment fitted. Ask us or your plumber how to protect the toilet bowl and waste traps while maintaining a seal against drain smells.

Insulation is extra protection

Call us for details of our winter insulation pack

04 / THROUGHOUT THE YEAR

Keep your hut
breathing

Ventilation is equally important. Keep the trickle vents open and unobstructed to allow airflow through the hut and help prevent condensation and damp building up inside.

Use the extractor fan, where fitted, during and after showering or cooking. Wipe away condensation and leave space for air to circulate around furniture.

During winter closure

Keep permanent ventilation open, clear leaves and stored items from beneath the hut, and check inside periodically for damp or leaks.

When you return

Follow the equipment instructions to recommission the water system, flush it through and check for leaks. Make sure the water heater is completely full before switching it back on.

05 / A FEW OTHER THINGS

Small checks. Fewer surprises.

Roof & rainwater

Look for loose fixings, damaged seals or signs of leaks, particularly after storms. Keep gutters and outlets clear where fitted. Arrange safe access for any work at height.

Seals & fittings

Check around windows, doors, the shower and kitchen for deteriorating seals or small leaks. Attend to these promptly and keep hinges and locks operating freely, following the fitting manufacturer’s advice.

Chassis, wheels & steps

Look for damaged protective finishes or corrosion on exposed metalwork. Check that steps and handrails remain secure.

Appliances & alarms

Follow the servicing and descaling instructions for your water heater and other fitted appliances. Test smoke alarms and any carbon monoxide alarms as their manufacturers direct. Use a qualified professional for electrical repairs.

06 / IF ACCESS IS EVER NEEDED

Designed to come apart simply

If a pipe or cable ever needs attention, the external cladding can be removed to expose the insulation and services behind it.

Wooden huts

Remove one or two of the wooden corner posts, then unscrew the individual cladding boards to expose the insulation and the services behind it.

Metal-clad huts

Remove one or two of the corner trims, then unscrew the individual cladding sheets to expose the insulation and the services behind it.

The hut is reassembled by reversing the same steps, taking care to reinstate insulation, any protective membranes, seals and trims correctly.

Before drilling or opening a wall: check where pipes and cables run. If a screw has damaged a service, stop work and have the affected supply safely isolated. Contact us for access advice and use a qualified tradesperson for the repair.

A little attention now. A hut to enjoy for years.